Allied Marine logo
 

Charlie's Tuna
1999

$ 250,000
Plymouth, MA, US

INQUIRE ABOUT THIS YACHT
GENERAL DESCRIPTION

Custom Built Fly bridge built from 1/4" 5058 Aluminum plating 5" x 4" 6061 Rib construction 24" on center. 5 Stateroom 3 head layout, Large salon, lower helm and controls on Fly bridge. New twin Lugger -L6140AL2.3 six cylinder diesels with less than 400 hours. Twin Disc MG5114V 1.8:1 Gears w/ 2.75" shafts w/ PSS Dripless shaft seals. 28 Knots WOT.

Specifications

Name Charlie's Tuna
Price $ 250,000 USD
Year 1999
Location Plymouth, MA, US
Hull Material Aluminum

Engines

Engine 1
Engine Location Port
Drive Transmission V
Power 700|horsepower
Fuel diesel
Hours 375
Engine Make Lugger
Engine Model L-6140AL2.3
Model Inboard
Engine Year 2013
Engine 2
Engine Location Starboard
Drive Transmission V
Power 700|horsepower
Fuel diesel
Hours 375
Engine Make Lugger
Engine Model L-6140AL2.3
Model Inboard
Engine Year 2013

Additional Information

Builders description

Charlie's Tuna Specifications:

General:

 Year Built: 1999

 Owner/Builder: Charles S. Breen

 Specification Hull:

LOA: 62' 0"

 LWL: 51' 0"

 Beam: 16' 4"

 Draft: 4' 0"

 Displacement: 52,000 lbs (Dry)

Fuel Capacity: 1500 gal.

Hull Plating: .25" 5058 aluminum

 Keel: .5"x 6" 6061 aluminum

 Ribs: .5"x 4" 6061 aluminum (24" oc)

 Stringers: .5" x 1.5" 6061 aluminum (12" oc)

 Transom: .5" 5058 aluminum

 Engine Beds: 3.5"x 8" x .375" 6061 aluminum

Dead Rise: 19 degrees

 Chines: Single 8" hard

 Welding: All seams, triple TIG welded outside, Triple MIG welded inside with matched hull alloy.

Specification Running Gear:

Engines: Twin Lugger-L6140AL2.3, 6 cylinder diesels, 700hp @ 2100 rpm (each) Serial Number: Port: 1401-2567, Stb. 1401-2568

Engine Hours: Port: less then 400 Stb.: less then 400

Transmission: Twin Disk Model: MG5114IV 1.8:1, 14 degree dn. angle; Serial No.: Port: TBD Stb.: TBD

Shafts: 2.75"

 Shaft Seals: PSS Dripless

 Shaft Struts: 1.75 SS316 with 2.75x10" Cuttlas Bearings

Propellers: 30x34" 5 Blade, Katapult

Rope Cutter: Shaft Shark SS700 (2.75")

Performance: 28 knots WOT at 2100rpm (600 gal fuel load)

Fuel Consumption: 26 gph per engine at WOT

Rudder Shafts: 2.5" SS316 with dual cuttlas support and O-Ring seal.

Rudders: Foil Shaped welded SS316 30"x14"

Thru Hull fittings: Marelon, reinforced poly-carbonate

Disclaimer
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.
DISCLAIMER

Allied Marine is pleased to assist you in the purchase of this vessel. This boat is centrally listed by South Shore Dry Dock Marine, Inc..

CONTACT AN ALLIED MARINE SPECIALIST