Allied Marine logo
Profile Makarios Top view Bow view Scenic Scenic Bow View STB Profile running Cruising Profile Cockpit table and seating Salon Galley Guest stateroom VIP Stateroom Master Stateroom Engineroom

2011 59.42 ft

$ 1,395,000
Anacortes, WA, US


A must see, beautiful new gray hull!  t.


Name Makarios
Price $ 1,395,000 USD
Year 2011
Length Overall 59.42 ft
Draft 4.75 ft (Max)
Beam 16.75 ft
Location Anacortes, WA, US
Hull Material Fiberglass


Engine 1
Engine Location Port
Drive Transmission Direct
Power 454|horsepower
Fuel diesel
Hours 978
Engine Make Caterpillar
Engine Model C-7
Model Inboard
Engine Year 2011
Engine 2
Engine Location Starboard
Drive Transmission Direct
Power 454|horsepower
Fuel diesel
Hours 978
Engine Make Caterpillar
Engine Model C-7
Model Inboard
Engine Year 2011

Additional Information

Hull, Superstructure and Decks
  • Hand laid, gel coated fiberglass hull
  • Airex C70.90 foam on hull sides
  • AL 600 Balsa core on superstructure
  • Solid fiberglass hull bottom
  • Deck access hatch to chain locker
  • Cockpit hatch with ladder down to lazarette
  • White non skid fiberglass deck
  • White vinyl rub rail stainless steel insert
  • Black sigle boot top stripe
  • Two coats of Seahawk or equal primer, an epoxy barrier coat and covered with two coats of Seahawk or equal anti-fouling bottom paint
  • From cockpit to FB hatch with stainless steel frame with Glass cover insert
  • Teak swim platform and steps
  • Teak deck from cockpit sidewalk
  • Light grey paint hull
  • "S-bow"
  • Vinylester resin
  • Sunbrella fabric on outside cushions
  • Diamond Sea-glaze sliding door for PH, Dutch doors for salon
  • Fiberglass swim platform w/ swim ladder
  • Fiberglass stairs from starboard side deck to FB
  • Frameless window frames
  • Tempered dark tinted window glass
  • Transom door
  • Screens on all port lights, screen/shade for hatches
  • Side boarding gate at port side cockpit
  • Deck lights, 24V
  • Portuguese bridge with lockers with settee
  • Skylight hatch on PH top
  • Hard top with fiberglass mast and ventilation hatches
  • Detailed carbon fiber reinforced structural stringers in engine room and lazarette
  • Windshield on FB, Lexan
Exterior Hardware and Fittings
  • Stainless steel hardware
  • 1-1/2" Stainless steel handrails and 1-1/4" stanchions
  • Stainless steel square port lights
  • Stainless steel cleats and hawse holes
  • Horizontal windlass Mavwell HWC2200 single anchoring system with fiberglass bow pulpit
  • Removable life line for aft FB railing
  • Zincs on rudder and shaft
  • Stainless steel handrails on back transom
  • Fwd deck handrails with safety line
  • Lifeline for boat deck rails
  • Fuel fills both side decks
  • Two STIDD helm seats in FB and one Stidd helm seat in PH
  • Exhaust pipe and muffler upgrade to match new requirements. Includes custom wedge on hull
  • Two STIDD helm seats in FB and two Stidd helm sesat in PH
  • Fiberglass skeg protected propeller and rudder
  • Strut with cutlass bearings
  • High-efficiency, computer-designed and machined Bronze Proper w/ prop guard
  • Teak steering wheel inside and stainless steel on FB
  • Teak stern staffs
  • Windshield wipers and washers
  • Remote operated lockable cockpit hatch
  • Aft deck shower, dock side water
  • Fresh and sea water-wash down in cockpit and foredeck
  • 1-1/2" S/S handrails around top deck
  • Trim tabs
  • FB air conditioning 2400BTU
  • S/S plow type anchor-80lbs
  • FB Polycarbonate full-enclosure 
  • 14' Walker Bay w/50HP 4 stroke Honda
  • Kayaks with custom storage cradle (1 x Malibu, 1 x Hobie Tandem)
  • Paddleboard with custom storage cradle.
  • Lee cloth around boat deck s/steel railing
Control and Navigation
  • Dual control stations-PH and FB (Autopilot control on Helmchair arm)
  • Complete engine instrumentation system
  • Engine gauges to bevel panel in PH
  • Wet exhaust and including water temperature, oil pressure, hour meter and start/stop controls in engine room and remote start/stop controls in the PH
  • Power steering system
  • Hydraulic control station in cockpit w/hinged wing box
  • Glendinning electronic engine controls
  • Hynautic steering system
  • Engine alarm system, audio oil, temperature and hour meter
  • Kehlenberg trumpet in air horn
  • Hydraulic Keypower stabilizer
  • Hydraulic bow thruster and stern thruster
  • Upgraded stabilizer fins - now 9sq/ft
  • KVH V3 Sat Phone

  • DBC 8 Person Life Raft Rail Deploy

  • Flir 625XP Hi Def Camera with Dual Control Stations

  • Key Power Hydraulic Alternator 150 AMP Direct Charge

  • ARC Global Fix EPIRB

Electrical System
  • Heavy-duty batteries
  • Engine battery disconnect switch
  • AC outlets throughout
  • Battery paralleling system with control switch Service battery switch
  • 4000W inverter/charger
  • Polarity reverse indicating light
  • Bonding system throughout
  • Cellular amplifier
  • VOLT and AMP meters
  • Mastervolt battery charger
  • GFI AC outlet with SmartLock feature for operation error protection which exceeds UL
  • requirements
  • UPS electrical protection
  • 24V lights in all compartments
  • AC/DC distribution panel with magnetic circuit breakers
  • Shore power receptacle 1x50AMP in transom NMEA2000 BACKBONE w/AC/DC power installed w/cable master in transom
  • Steel-head davit 3 function hydraulic davit SM1500R
  • Shore power cords, wired directly into GFI protected shoreline breakers
  • Keypower battery charging system
  • Chart light beside dash
  • Maretron DSM250NMEA2000 Display PH, FB and MSR
Engine Room and Bilge
  • Caterpillar C-7 x 2 (978hours)
  • Flojet pressure fresh water system
  • Johnson pressure sea water system
  • Fuel manifold distribution system
  • Dripless seal for rudder post
  • 20 gallon water heater
  • aluminum fuel tanks with sight gauges
  • Stainless steel water tanks with sight gauges
  • Color-coded piping for fuel and water
  • Common drainage system for sink, shower, bilge and exterior deck
  • Electric bilge pump 24V auto and manual bilge switch, sumped when available
  • 24V shower sump pump
  • High water bilge alarm in all bilge pump zone
  • Spare conduit running from engine room to PH, engine room to FB, and engine room to FB overhang
  • Holding tank plumbed dockside or overboard discharge
  • Holding tank gauge in PH
  • Generator exhausts to be water-drop type per "Centek", "marine Exhaust Co." or equal Dripless engine shaft seal log
  • Cruisair compressors for central air conditioner, 4 units, total 76K BTU
  • Five ceiling lights in engine room
  • Fresh Water outlet with hose for engine and generator
  • Bronze sea cocks and raw water strainers on all intakes
  • Oil changing system for engine and generator
  • Racor fuel/water separator w/Y-valves for engine and generator
  • S/S engine beds
  • Engines isolation switch
  • Haron-rib rubber floors for engine room walkway
  • One manual bilge pump
  • AC outlet
  • Lighted bilge
  • Fresh water outlet with hose for engine and generator
  • 3 valves in steering system for autopilot
  • Fiberglass exhaust pipes with mufflers
  • TaylorMade air conditioner pumps, P1000C for lower deck, P1000C for Main deck
  • All engine room and machinery spaces shall be primed and top coated with polyurethane paint system
  • fire extinguisher system with engine shutdown system
  • Rafrigerant type is accepted worldwide under the Montreal Protocols
  • Northen Lights generators 12kw (928 hours) and 6kW (302 hours) w/wavenet controls.
  • Generator set resiliently mounted and installed with sound shield
  • Fresh-water flush system in place on main engine and generator sea strainers
Accommodation and interior
  • Teak paneling and cabinetry
  • Stainless steel hardware
  • Soft vinyl headliners
  • Cruisair SMXHT Vimar style control panels
  • Push button handles for drawers and cupboards
  • Seagull water purifier
  • Removable headliner
  • 4.5mm thickness 5052 Aluminum fuel tanks with sight gauges and tested to International Standards 33CFR w/ high and low fuel level alarm system
  • 2mm thickness 316 Stainless steel water tanks with sight gauges
  • Tank tender for 4 tanks
  • Stain varnish for interior finish
  • Painted flooring prepared for carpet throughout, except Natural teak and holly flooring in PH, heads, galley and salon
  • Mattresses for berths
  • Maytag 2400AWW stacked washer/dryer
  • Spare conduit running from engine room to PH engine room to FB overhang
  • Holding tank plumbed dockside or overboard discharge
  • Holding tank gauge in PH
  • Dripless eingine shaft seal log
  • Watermaker preparation
  • Gulfcoast Fuel polishing system based on US Military Abrahams M1 Tank design
  • Delta-T engine room vent blowers
  • Hanging lockers w/ dual locking mechanism
  • Phantom screen
  • Silestone top for cabinet across / adjacent to galley in salon
  • Natural teak and holly flooring
  • Settee with storage under
  • Steering control system
  • Teak grab rail on ceiling
  • Cruisair SMXHT Vimar style control panel
  • Engine gauges on bevel panel
  • Ritchie compass
  • Stidd Chair 500N Slimline x 2
  • Windshield defrosters
  • Ritchie compass 5"
  • Lighted stairway to fore cabin
  • 24V LED lights
  • Water tight sliding doors to side decks
  • Teak valance board
  • Teak top dinette table
  • Bomar hatch with dual screen
  • 24V LED lights
  • Entertainment center and storage cabinet
  • Salon dutch doors
  • Natural teak and holly flooring in salon
  • Sony 32" LCD TV with High-Low lift
  • L-shape Salon settee with storage
  • U-Line ice maker
  • Hydraulic hi-low teak top table
  • Watertight hinge door to cockpit
  • Teak valance board
  • Teak grab rail on ceiling
  • Cruisair SMXHT Vimar style control panel
  • Home theater DVD / CD radio system
  • Nautical star pattern on salon floor
Master Stateroom
  • Queen size berth, w/ flip up storage underneath
  • Cruisair SMXHT Vimar Style control panel
  • Sony 32" LCD TV and DVD / CD system
  • Dressing mirror behind door
  • Cedar lined hanging locker w/ auto lighting
  • Stainless steel square port lights
  • 24V LED lights
  • Escape hatch from guest stateroom to master stateroom
Guest Stateroom
  • Queen size berth with drawers and storage underneath
  • Cruisair SMXHT Vimar style control panel
  • Sharp 20" LCD TV and DVD / CD system
  • 24V LED lights
  • Cedar lined hanging locker w/ auto lighting
  • Dressing mirror behind door
  • Soft vinyl on hull side
  • Stainless steel square port light with S/S storm cover
  • Silestone counter tops (Mahogany)
  • Teak walls and cabinets
  • Stall showers with one piece glass door in master and guest heads
  • Grohe faucet for sink and shower
  • Medicine / cabinet storage
  • 24V LED light
  • Natural teak and holly flooring
  • Stainless steel square port light with screen
  • Tecma heads
  • GFI AC outlet
  • Mirror
  • Vent blower
  • Silestone counter tops (Mahogany)
  • Teak panel and cabinetry
  • Storage cabinets and drawers
  • Serving shelf / dish locker
  • Franke sink with tap
  • Natural teak and holly flooring
  • 24" Gaggenau gas top with matching 24" Gaggenau electric oven
  • Refrigerator Subzero 700
  • Overhead dish locker
  • Overhead microwave convection oven with exhaust blower
  • GFI AC outlet
  • GE garbage disposal
  • Fisher and Paykel Dishwasher
  • U-line refrigerator/freezer in outside galley cabinet
FURUNO Navigation Package
  • FURUNO MFD Black Box Processors
  • FURUNO6kw 4ft Open Array Dual Ranging Rader
  • FURUNO Class B AIS Integrated into Radar and Chart Plotter
  • FURUNO Digital Sounder with 1kw B260 Broadband Transducer
  • 19" Ambinent Nav Marine Monitors in PH and FB
  • AXIS IP Camera in Engine Room and Aft Deck and side decks
  • ICOM 604 VHF in PH and FB
  • Simrad AP28 Autopilot system at PH and FB
  • Redundant Meretron NMEA 2000 GPS, Depth Sounder and weather Station
  • Nobeltec Navigation Computer
  • Maretron DSM250 NMEA 2000 Display at PH, FB and MSR
  • KVH M7 Control Panel Satellite HDTV System
  • Maretron TSM1330 display in PH
Maintenance and work performed by Phil Brooks


Ocean Alexander 60 mv 'Makarios'

Upgrades performed at Philbook's Boatyard August 2010 - April 2013

W/O 15019 August 2010

1- Replaced Pomponette helm chairs with Stidd chairs.

2- Replaced teak flag poled with custom SS poles and covers.

3- Extended light mast to accommodate courtesy flags.

4- Fabricated and installed hammock stands and sockets for boat


W/O 15085 October 2010

1- Installed Kabola HR 500 hydraunic furnace.

2- Fabricated and installed teak treads for stairs to bridge.

3- Wire block heater to sub panel in lazerette.

W/O 15159 January 2011

1- Upgrade 10" bow thruster and tube to 12" 25hp.

2- Trim vessel with lead under closet in crew's stateroom.

W/O 15250 April 2011

1- Install Headhunter Mach IV domestic water pump.

2- Fabricated new cushions and covers for flybridge settee.

W/O 15367 June 2011

1- Fabricated and installed railing covers for boat deck.

2- Modified railings and tie downs for Whaler

W/O 15493 August 2011

1- Supply and install back up DC domestic water pump.

2- Install radar array Furuno DRS6A

3- Fabricate and install name board / running lights.

4- Modify existing lower helm table and install Scandvik electric

center ram to raise for eating and lower for sleeping.

5- Install 4-Ocean LED 2010 underwater lights

6- Install Spectra Newport 1000 MK watermaker with Z-brane

7- Fabricate and install toolbox base.

W/O 15744 March 2012

1- Fabricate and install teak decking for side decks and around

front of Portuguese dodger.

2- Fabricate teak cockpit table with ebony inlay and finished with

awlbrite. Mount on 'Seafurniture duel pedestal base.

3- Fabricate cockpit seating with cushions and covers.

4- Modify galley and install trash compactor.

5- Fabricate and install full extension drawers across from galley.

6- Installed new table for upper bridge settee.

7- Fabricate and install SS railings around swim grid

W/O 16002 July 2012

1- Replace house batteries with Discover AGM 8D

W/O 16077 September 2012

1- Upgrade all batteries. Recently replaced house bank rewired to

act as main engine start batteries. Install and wire 8 Discover

AGM EV512 slimlines as house bank in lazerette between

engine stringers against transom.

2- Modified storage in crews closet

3- Install fan and ventilation for crew's quarters.

4- Fabricate and install bookshelf in main salon port side aft


5- Replaced davit with Steelhead ES 1500 and relocated to aft

port corner of boat deck. Boat deck was reinforced as per

drawings from Greg Marshal and 2 matching compression posts


were fabricated and installed. (port side sched 80 and

starboard side sched 10)

6- Installed 6KW northern lights generator with Wavenet controls.

Existing 12 KW Northern lights upgraded to Wavenet.

7- Replaced horn with Kahlenberg model DOA horns

8- Fabricate and install Maretron TSM 1330 including backbone

and monitoring of batteries, power tanks, engines, generator

and Internet etc.

W/O 16330 January 2013

1- Install control 4.

2- Install Yamaha receiver and blu-ray in main salon.

3- Install MIC for cockpit.

4- Replace KVH with Intellian S6 HD dome.

5- Replaced engine digital displays with color screens.

6- Replace Fusion control head and remotes with MS700 and

integrate with !pad.

7- Install 'teak' carpet on bridge and steps.

8- Added 500 Lbs of lead under v-berth.

9- Repainted bootstripe.


In addition there was the regular maintenance of mechanical systems

and exterior finishes.

If you would like further information please don't hesitate to contact


Jamie Hansen

250-656-1157 Office

250-857-5160 Cell






The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.


Allied Marine is pleased to assist you in the purchase of this vessel. This boat is centrally listed by Alexander Marine USA.